PipeWire Audio System Overview


AGL uses the PipeWire daemon service to provide audio playback and capture capabilities. PipeWire is accompanied by a secondary service, WirePlumber (also referred to as the session manager), which provides policy management, device discovery, configuration and more.

Applications can connect to the PipeWire service through its UNIX socket, by using the libpipewire library as a front-end to that socket.


The Audio System’s configuration is mainly done in the session manager. The session manager is the service that dictates policy, therefore this is the place to configure options such as device properties, device priorities and application linking policy.

An extensive listing of configuration options for the session manager, WirePlumber, is available in the next chapter, Session Manager Configuration


WirePlumber supports runtime configuration of devices, through the wireplumber-cli tool. This tool supports the following sub-commands:

  • wireplumber-cli ls-endpoints: This lists all the known audio endpoints, including devices and applications that are streaming. In front of the devices, there is a * (star) character on the “default” device, i.e. the device that is chosen by default to link applications to. The volume and mute status of the devices is also shown.
  • wireplumber-cli set-default [id]: Changes the default endpoint of a specific category (capture or playback, determined automatically by the endpoint’s type) and sets it to be the endpoint with the specified [id]. The id is the number shown in front of each endpoint’s name in ls-endpoints.
  • wireplumber-cli set-volume [id] [vol]: Sets the volume of [id] to [vol]. [vol] must be a floating point number between 0.0 (0%) and 1.0 (100%).
  • wireplumber-cli device-node-props: Lists all the properties of the device nodes, useful for writing .endpoint configuration files, as discussed in the Session Management Configuration chapter.

Due to a system limitation, before running this tool on the command line, you need to export the XDG_RUNTIME_DIR environment variable, like this:

export XDG_RUNTIME_DIR=/run/user/1001


PipeWire also ships with /etc/pipewire/pipewire.conf, which can be used to configure which pipewire modules are being loaded in the PipeWire deamon. You should normally not need to modify anything there, unless you understand what you are doing.


Native API - libpipewire

The main entry point for applications to access the audio system is the API offered by libpipewire. The functionality offered by libpipewire is vast and it is beyond the scope of this document to describe it all.

For playback and capture, applications should use struct pw_stream and its associated methods. There are usage examples for it in the PipeWire source code.

For convenience, applications that use GStreamer can use the PipeWire GStreamer elements to plug the functionality offered by struct pw_stream directly in the GStreamer pipeline. These elements are called pwaudiosrc and pwaudiosink


gst-launch-1.0 audiotestsrc ! pwaudiosink

Through these elements, it is possible to specify the application role by setting it in the stream-properties property of the element, as shown below:

gst-launch-1.0 audiotestsrc ! pwaudiosink stream-properties=p,media.role=Multimedia

or, in the C API:

gst_util_set_object_arg (sink, "stream-properties", "p,media.role=Multimedia");

When using these GStreamer elements, applications should handle the GST_MESSAGE_REQUEST_STATE message on the bus and change their state accordingly. This message will be sent when the session manager requests a change in the state due to a higher priority stream taking over.

ALSA Compatibility

AGL offers a virtual ALSA device that redirects audio to PipeWire through an ALSA PCM plugin. This device is the default one, so unless you explicitly specify a device in your ALSA client application, audio will go through PipeWire instead.

This mode has limitations, however.

  • There is no way to specify the role of the application. WirePlumber will always assume it is a “Multimedia” application
  • There is no way for the application to be notified when another stream takes over. When this happens, the audio clock will simply stop progressing and the ALSA API will likely block.

Audiomixer service

See the separate agl-service-audiomixer documentation.

Runtime mechanics

The PipeWire service is activated on demand, via systemd socket activation. The WirePlumber service is always started and stopped together with the PipeWire service.

If you wish to manually start/stop/restart the service, you can do so by using systemctl:

systemctl start/stop/restart pipewire@1001.service


When something is wrong with the audio setup, it is useful to know how to debug it…

PipeWire & WirePlumber

The PipeWire and WirePlumber daemons can be configured to be more verbose by editing /etc/pipewire/environment

  • Set G_MESSAGES_DEBUG=all to enable WirePlumber’s debug output.
  • Set PIPEWIRE_DEBUG=n (n=1-5) to enable PipeWire’s debug output.

All messages will be available in the systemd journal, inspectable with journalctl.

PIPEWIRE_DEBUG can be set to a value between 1 and 5, with 5 being the most verbose and 1 the least verbose.

AGL applications & services (AppFW)

For AGL applications and services that are installed by the app framework, you can set the PIPEWIRE_DEBUG environment variable in /etc/afm/unit.env.d/pipewire. This will enable the debug messages that are printed by libpipewire and will make them available also in the systemd journal.